larouci2
عضو أساسي
Device : Xiaomi Redmi Note 9 Pro
Operation : Reset Mi Account (New)
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
SAMSUNG : Turn Off phone, hold EDL Cable Button and insert to phone and
press VOL DOWN + POWER on phone more than 3 times rapidly and then leave EDL Cable Button.
SAMSUNG (NEW) : Turn Off phone, hold EDL Cable Button and insert to phone and
press VOL UP + DOWN on phone more than 3 times rapidly and then leave EDL Cable Button.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM270)
Driver Info : Qualcomm Incorporated, qu_usb_serial.sys, 2.1.2.0
Connecting to phone...OK
Waiting for response...OK
Init Handshake Sequence...OK
Hardware ID : E1901400 [SM6250] 00007200
OPK_DATA : 4B60244704D721E5B96DD5BB7233886E38F2198FBDE6433FCE 1D25A7B0472DD7
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [SM6250]...Done
Executing Loader...OK
Auth Enabled Device! You may need Mi Auth Account to service!
Init EDL Auth...OK
Detecting Storage Type...OK
Hardware : SM6250, UFS, 128 GB
LU Count : 6 [0x01CB9800] [0x00000800] [0x00000800] [0x00008000] [0x00100000] [0x00008000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 262144 [65536], Out: 16384, Sector Size: 4096
Reading Partition Table...OK [90]
Reading Device Information...OK
Device : Xiaomi
Software : , V13.0.5.0.SJZEUXM [Thu Jan 5 01:21:09 CST 2023]
Android Ver. : 12
Patch Level : 2022-12-01
Reading Data[1]...Done
Patching Data...Done
Writing Data...Done
Reading Data[2]...Done
Patching Data...Done
Account : 417905847
Phone : +4958*****20
Display ID : 46UR-VO4K-JNC4QS
Writing Data...Done
Operation Finished.
QcFire Ver. 10.2
Operation : Reset Mi Account (New)
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
SAMSUNG : Turn Off phone, hold EDL Cable Button and insert to phone and
press VOL DOWN + POWER on phone more than 3 times rapidly and then leave EDL Cable Button.
SAMSUNG (NEW) : Turn Off phone, hold EDL Cable Button and insert to phone and
press VOL UP + DOWN on phone more than 3 times rapidly and then leave EDL Cable Button.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM270)
Driver Info : Qualcomm Incorporated, qu_usb_serial.sys, 2.1.2.0
Connecting to phone...OK
Waiting for response...OK
Init Handshake Sequence...OK
Hardware ID : E1901400 [SM6250] 00007200
OPK_DATA : 4B60244704D721E5B96DD5BB7233886E38F2198FBDE6433FCE 1D25A7B0472DD7
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [SM6250]...Done
Executing Loader...OK
Auth Enabled Device! You may need Mi Auth Account to service!
Init EDL Auth...OK
Detecting Storage Type...OK
Hardware : SM6250, UFS, 128 GB
LU Count : 6 [0x01CB9800] [0x00000800] [0x00000800] [0x00008000] [0x00100000] [0x00008000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 262144 [65536], Out: 16384, Sector Size: 4096
Reading Partition Table...OK [90]
Reading Device Information...OK
Device : Xiaomi
Software : , V13.0.5.0.SJZEUXM [Thu Jan 5 01:21:09 CST 2023]
Android Ver. : 12
Patch Level : 2022-12-01
Reading Data[1]...Done
Patching Data...Done
Writing Data...Done
Reading Data[2]...Done
Patching Data...Done
Account : 417905847
Phone : +4958*****20
Display ID : 46UR-VO4K-JNC4QS
Writing Data...Done
Operation Finished.
QcFire Ver. 10.2