- إنضم
- 27 فبراير 2016
- المشاركات
- 1,876
- مستوى التفاعل
- 1,741
- النقاط
- 113
فلاشة CONDOR_L2_Pro RAM_3Go . ROM_32Go مسحوبة علي NckBox AndroidMTK
بعض الصور من الهاتف
معلومات الهاتف
Action : Boot Info.
Selected 0-By CPU:ELBRUS
Exe version: NCKBox AndroidMTK 1.8.9.8
Reinsert phone battery.
Battery must be charged.
Phone must be off with battery inside.
Please insert USB cable now...
Detected : MediaTek PreLoader USB VCOM (Android) (COM11)
Boot mode: Preloader
BBCHIP: 321 0 ca00
Using Algo 2.
Phone detected...Please wait
Sending DA agent, please wait...
----------------------------------------------------
BaseBand CPU :MT6737T
BaseBand CPU Secure Version : FF
BaseBand CPU Bootloader Version : 02
----------------------------------------------------
INT RAM: 128 KB SDRAM
EXT RAM: 3 GB DRAM
----------------------------------------------------
EMMC: (233Gb+24576Mb) SAMSUNG 0x474436424d42
EMMC FW VERSION: 01:00:00:00:00:00:00:00
EMMC CID: 150100474436424D42 : 00000000000000
EMMC UA SIZE: 0x747c00000
BOOT STYLE: EMMC BOOT
FULL LENGTH: 0x748800000 [29.133 GB]
Status: USB_HIGH_SPEED
Detecting high speed port, wait......
If driver not installed, install high speed port driver.
If not need high speed port, disable it.
After repeat opperation.
Detected : MediaTek DA USB VCOM (Android) (COM24)
Build ID: O11019
Display ID: SP633_V09_20181220
Version: 8.1.0
Build Date: Thu Dec 20 13:51:41 CST 2018
Build Date: 1545285101
Model: Plume L2 Pro
Brand: Condor
Device: Plume_L2_Pro
Manufacturer: SPA Condor Electronics
This phone have FRP partition.
IMEI[1]: 300000000000000
IMEI[2]: 300000000000000
Read done.
Wait untill phone will start charging.
All done.
معلومات قراءة الفلاشة
Reinsert phone battery.
Battery must be charged.
Phone must be off with battery inside.
Please insert USB cable now...
Detected : MediaTek PreLoader USB VCOM (Android) (COM11)
Boot mode: Preloader
BBCHIP: 321 0 ca00
Using Algo 2.
Phone detected...Please wait
Sending DA agent, please wait...
----------------------------------------------------
BaseBand CPU :MT6737T
BaseBand CPU Secure Version : FF
BaseBand CPU Bootloader Version : 02
----------------------------------------------------
INT RAM: 128 KB SDRAM
EXT RAM: 3 GB DRAM
----------------------------------------------------
EMMC: (233Gb+24576Mb) SAMSUNG 0x474436424d42
EMMC FW VERSION: 01:00:00:00:00:00:00:00
EMMC CID: 150100474436424D42 : 00000000000000
EMMC UA SIZE: 0x747c00000
BOOT STYLE: EMMC BOOT
FULL LENGTH: 0x748800000 [29.133 GB]
Status: USB_HIGH_SPEED
Detecting high speed port, wait......
If driver not installed, install high speed port driver.
If not need high speed port, disable it.
After repeat opperation.
Detected : MediaTek DA USB VCOM (Android) (COM24)
Build ID: O11019
Display ID: SP633_V09_20181220
Version: 8.1.0
Build Date: Thu Dec 20 13:51:41 CST 2018
Model: Plume L2 Pro
Brand: Condor
Device: Plume_L2_Pro
Manufacturer: SPA Condor Electronics
Dumping Preloader.
Start dumping flash, this can take up to 1 hour.......
Start processing proinfo
Reading: BEGIN: 0x80000 - LEN: 0x300000
Start processing nvram
IMEI[1] from NVRAM: 358181091671764
IMEI[2] from NVRAM: 358181091671772
Start processing protect1 ......
Reading: BEGIN: 0x880000 - LEN: 0xa00000
Start processing protect2 ......
Reading: BEGIN: 0x1280000 - LEN: 0xa00000
Start processing lk ......
Start processing boot
Start processing recovery
Start processing logo ......
Start processing secro
Reading: BEGIN: 0x5200000 - LEN: 0x600000
Start processing trustzone
Start processing persist ......
Reading: BEGIN: 0x6a80000 - LEN: 0x3000000
Start processing frp ......
Reading: BEGIN: 0x9a80000 - LEN: 0x100000
Start processing nvdata ......
Reading: BEGIN: 0x9b80000 - LEN: 0x2000000
Start processing odmdtbo
Reading: BEGIN: 0xbb80000 - LEN: 0x1000000
Start processing vendor
Reading: BEGIN: 0xf000000 - LEN: 0x20000000
Start processing system
Reading: BEGIN: 0x2f000000 - LEN: 0xbb800000
Saved to : C:\Users\HASSAN_MOBIL_\Documents\Android_MTK\firmware_backup\MT6737T_EMMC_Condor_Plume L2 Pro_8_1_0_2019_01_28_13_25)
Wait untill phone will start charging.
All done.
معلومات الهاتف على InfinityBox CM2MTK
Operation : Check / Read Info [ v1.58 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 11 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6735
BB_CPU_NME : [MediaTek] MT6735_S00
BB_CPU_EXT : 0xCC00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0002
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v3.3001.00.00
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x9B
NAND Flash : NOT INSTALLED
eMMC Flash : 470001154D42364453560142CBDB6E9B
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BMB6D
[eMMC] : FLASH_CID : 150100474436424D420156539B6E65CB
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x0000000747C00000
[eMMC] : FLASH_UCP : 29820 MiB [eMMC 32 GiB]
DEV RID : 0x065549176A3C9A7E30447F20133BD1A5
INT RAM : 0x00020000
EXT RAM : 0xC0000000 [3 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
[AP] : Initial info read Ok!
Brand : Condor
ProdName : Plume_L2_Pro
ProdModel : Plume L2 Pro
Device : Plume_L2_Pro
AndroidVer: 8.1.0
SECURITY :
IMEI_SW [1] : 615E1F1D8EA65BF
IMEI_SW [2] : 615E7F1D8EA6DBF
BTMAC Addr : FCFF00000000
WiFi MAC : 0000FAFFFFFF
Done!
Elapsed: 00:00:08
Reconnect Power/Cable!
رابط التحميل
https://mega.nz/#!l0kilSDI!42NuqKJCQPRt51HieEf7rgkF5e9bUKaEUWjoCgjsSeI
التبويت توصيل الهاتف فقط
في رعاية الله وحفضه
التعديل الأخير: