مشكلة في condor c6

الحالة
مغلق و غير مفتوح للمزيد من الردود.
الذئب الجزائري

الذئب الجزائري

عضو أساسي
إنضم
18 جويلية 2014
المشاركات
436
مستوى التفاعل
85
النقاط
28
سلام عليكم اخوتي الكرام عندي مشكلة في موت جهاز كوندور سي 6

Chinese Miracle II [MTK module] v 1.57

Operation : Check / Read Info [ v1.57 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 3 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6583
BB_CPU_NME : [MediaTek] MT6583|6589_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.3.2 on BBID : 0x86
NAND Flash : NOT INSTALLED
eMMC Flash : 204A0190594E4958A8A1164881A0F1D1
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , HYNIX
[eMMC] : FLASH_CID : 90014A2058494E594816A1A8D1F1A081
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00200000
[eMMC] : FLASH_LEN : 0x00000000E7000000
[eMMC] : FLASH_UCP : 3696 MiB [eMMC 4 GiB]
DEV RID : 0xBF527ADD75808C293C373C93205EF735
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Info read not done :( Erased/damaged phone?

Done!
Elapsed: 00:00:15
Reconnect Power/Cable!


Scatter Load Ok , BaseBand : MT6589 , Project : MTK6589 , Storage : eMMC
Files found : 12 , Set to Flash : 11
Ready to Flash!

Operation : Flash [ v1.57 ]

======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 3 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6583
BB_CPU_NME : [MediaTek] MT6583|6589_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.3.2 on BBID : 0x86
NAND Flash : NOT INSTALLED
eMMC Flash : 204A0190594E4958A8A1164881A0F1D1
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , HYNIX
[eMMC] : FLASH_CID : 90014A2058494E594816A1A8D1F1A081
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00200000
[eMMC] : FLASH_LEN : 0x00000000E7000000
[eMMC] : FLASH_UCP : 3696 MiB [eMMC 4 GiB]
DEV RID : 0xBF527ADD75808C293C373C93205EF735
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

ScatCFG : BaseBand : MT6589 , Project : MTK6589 , Storage : eMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify : Enabled
Setting : HW verify : Enabled

BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Check eMMC compatibility
BL : eMMC supported by BootLoader!

BL : BatteryLevel : 4190 mV
BL : BatteryLevel Ok

BL : Flash Pre-Erase
Total blocks to Erase : 2
Erase : 0x0000000000880000-0x0000000000100000
Erase : 0x00000000029A0000-0x00000000A2860000
Flash Pre-Erase Done, time used : 00:00:00

SecCfg Passed , 1799
BMT remark not need. Will skip
Sending Preloader ...
Use : preloader_u970_5.bin
Preloader Sent , Init passed
SecCfg Passed , 1799
PartCount : FFFFFFFF
PartErr : Not initialized , will update PMT now ...
Repartition Failed! Something wrong with HW or BL? Try make "Flash Erase" first!

Operation Failed
Elapsed: 00:00:17
Reconnect Power/Cable!
 
إتبع ماذا قال الإنفو أولا make Flash Erase
 
اخي لقد اتبعت الانفو و لكن لم تنجح معي العملية
ممكن طريقة اخرى اد امكن
و شكرا مسبقا
 
جاء زبون يحمل نفس فلاش حملته لك
 
الحالة
مغلق و غير مفتوح للمزيد من الردود.
عودة
أعلى