..::khaled::..
:: Reseller ::, EFT Team,
Samasung I747 Boot Repair ok
EasyJtag Suite ver.: 1.7.0.2 / wxWidgets 3.1.0-W-U started.
Operating system ver.: ******************************.
For support and updates visit http://easy-jtag.com
Check security...OK
Initialising: SAMSUNG GT-S5830I Config ver.:1.00
I/O Level set to : 3000 mV
Box S/N: *************** ,FW Ver.: 01.51
Connecting to Target...
JTAG device: BCM21553
CPU IDCODE : 0x07B3617F Mfg.: 0x0bf, Part: 0x7b36, Ver.: 0x0
CPU Manufacturer: SST/Broadcom , CPU Name: BCM21553
Halting CPU...
Initialize hardware...
Starting target communication...
Detecting nand memory parameters ...
NAND flash device ID:00EC:0050 'NAND 512MB 1.8V 16-bit (Samsung)' found
NAND geometry: Blocks:00000800, Page size:4096 bytes , Block size:64 pages
Reading prtitions information to file...C:\Users\D3V\Desktop\SAMSUNG_GT-S5830I_0x00000000_0x00100000_partitions.pbin
Done with error(s)...
Reading dump to file...C:\Users\D3V\Desktop\SAMSUNG_GT-S5830I_0x00000000_0x00100000.bin
Reading 0x00100000 bytes from NAND adress 0x00000000
Dumped 1081344 bytes in 10.638608s (99.261 KiB/s) OK.
Erasing memory from 00000000 length 00100000
Erased blocks 0 to 100000 on NAND flash device 'NAND 512MB 1.8V 16-bit'
Checking NAND Image : E:\fouad\Reparation\mobile\box's\EasyJtag\Rcp and dumps\Samsung\s5830i\S5830I_Readed_From_Alive_Phone_BN.bin
File successefuly loaded!
Writing memory from file...E:\fouad\Reparation\mobile\box's\EasyJtag\Rcp and dumps\Samsung\s5830i\S5830I_Readed_From_Alive_Phone_BN.bin
NAND Write OK! Elapsed time: 997.476074s (135.510 KiB/s)
For support and updates visit http://easy-jtag.com
Check security...OK
Initialising: SAMSUNG GT-I8160P Config ver.:1.00
I/O Level set to : 2200 mV
Box S/N: ,FW Ver.: 01.52
Connecting to Target...
U8500 USB BOOTROM : device 04CC:8500 opened
success: set configuration #1
success: claim_interface #0
Sending XLOADER...
success: bulk read 4 bytes
Done.
JTAG device: U8500
CPU IDCODE : 0x4BA00477 Mfg.: 0x23b, Part: 0xba00, Ver.: 0x4
CPU Manufacturer: QUALCOMM , CPU Name: CORTEX A9
JTAG device: U8500
CPU IDCODE : 0x62286041 Mfg.: 0x020, Part: 0x2286, Ver.: 0x6
CPU Manufacturer: SGS/Thomson , CPU Name: NOVATHOR U8500 JRC
Halting CPU...
Initialize hardware...
Starting target communication...
Detecting emmc memory parameters of bank (0) ...
EMMC #0 : ID : 0x00000045 Name : SEM04G Size : 3.7 G , (7733248) Blocks
EMMC #1 : ID : 0x00000045 Name : SEM04G Size : 1.0 M , (2048) Blocks
eMMC flash device(s) found, Device ID : 0x00450000
EMMC Writing GPT...
eMMC Write OK! Elapsed time: 0.643037s (199.055 KiB/s)
EMMC Writing XLOADER...
eMMC Write OK! Elapsed time: 4.903280s (78.315 KiB/s)
EMMC Writing PIT...
eMMC Write OK! Elapsed time: 9.833563s (104.133 KiB/s)
EMMC Writing STE MEM INIT...
eMMC Write OK! Elapsed time: 5.157295s (99.277 KiB/s)
EMMC Writing PWR MGT...
eMMC Write OK! Elapsed time: 6.056347s (84.539 KiB/s)
EMMC Writing SBL...
eMMC Write OK! Elapsed time: 24.489401s (83.628 KiB/s)
EMMC Writing SBL2...
eMMC Write OK! Elapsed time: 22.339277s (91.677 KiB/s)
EMMC Writing PARAM...
eMMC Write OK! Elapsed time: 137.471863s (119.181 KiB/s)
EMMC Writing IPL MODEM...
eMMC Write OK! Elapsed time: 12.863736s (159.207 KiB/s)
All Done.
EasyJtag Suite ver.: 2.0.7.0 / wxWidgets 3.1.0-W-U started.
Operating system ver.: Windows 7 (build 7601, Service Pack 1).
For support and updates visit http://easy-jtag.com
Check security...OK
Initialising: SAMSUNG GT-I9000 Config ver.:1.00
I/O Level set to : 2800 mV
Box S/N:xxxxxxxxxxxxxxxx ,FW Ver.: 01.52
Connecting to Target...
Done with error(s)...
[B][COLOR="#FF0000"]Loading repair file: 'D:\mobile\box's\EasyJtag\Rcp and dumps\Samsung\I9000\SAMSUNG_GT-I9000_efs_v2_00.rcp'
[/B][/COLOR]Repair File ver. : FILL ME
Repair file options. : NONE
Easy-Repair file load OK!
Using EasyRepair Mode...
Checking repair data...
EasyJtag Suite ver.: 2.0.7.0 / wxWidgets 3.1.0-W-U started.
Operating system ver.: Windows 7 (build 7601, Service Pack 1).
For support and updates visit http://easy-jtag.com
Check security...OK
Initialising: SAMSUNG GT-I9000 Config ver.:1.00
I/O Level set to : 2800 mV
Box S/N: xxxxxxxxxxxxxxxx,FW Ver.: 01.52
Connecting to Target...
JTAG device: S5PC110
CPU IDCODE : 0x1BA00477 Mfg.: 0x23b, Part: 0xba00, Ver.: 0x1
CPU Manufacturer: QUALCOMM , CPU Name: CORTEX A8
Halting CPU...
Initialize hardware...
Starting target communication...
Detecting nand memory parameters ...
NAND flash device ID:00EC:0050 'NAND 512MB 1.8V 16-bit (Samsung)' found
NAND geometry: Blocks:00000800, Page size:1024 bytes , Block size:256 pages
NAND Writing EFS...
NAND Write OK! Elapsed time: 25.161133s (419.695 KiB/s)
All Done.
Z3X EasyJtag Software ver. 2.0.7.3
Loading eMMC Addon Firmware... IO: 3300 mV
Box S/N: ****************, ,FW Ver.: 01.52
CMD Pullup Level:876 mV
CMD Active Level:2475 mV
HiPower™ mode is off!
eMMC Device Information
EMMC CID : 15010056545530304DF71EED4BB7CF8A
EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 12/2012 Rev.0xF7
EMMC NAME: VTU00M , S/N: 518867895
EMMC NAME (HEX): 56545530304D00
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
H/W reset function [RST_N_FUNCTION]: 0x00
Backup saved: VTU00M_ 518867895_20160303_1525.extcsd
Done.
Running:SAMSUNG: MoviNAND Factory Reset...
Skip loading eMMC Addon Firmware
CMD Pullup Level:876 mV
CMD Active Level:2475 mV
Sending Smart Wipe Request...
Wiping Card... Please do not touch it!
Please don't forget to repair extCSD from backup!
Done.
Running:SAMSUNG: MoviNAND Reset + Format...
Z3X EasyJtag Software ver. 2.0.7.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:876 mV
CMD Active Level:2475 mV
EMMC ROM2/3 (Boot Partitions) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Sending Internal Reconfiguration Request...
Waiting configuration Apply!
Restoring configuration...
EMMC ROM2/3 (Boot Partitions) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Wiping Card... Please do not touch it!
Please don't forget to repair extCSD from backup!
Done.
extCSD file...C:\Program Files\Z3X\EASYJTAG\Backups\VTU00M_ 518867895_20160303_1525.extcsd
Running:Repair extCSD...
Z3X EasyJtag Software ver. 2.0.7.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:876 mV
CMD Active Level:2475 mV
Writing...
Done.
Z3X EasyJtag Software ver. 2.0.7.3
Loading eMMC Addon Firmware... IO: 3300 mV
Box S/N: ****************, ,FW Ver.: 01.52
CMD Pullup Level:855 mV
CMD Active Level:2495 mV
HiPower™ mode is off!
eMMC Device Information
EMMC CID : 15010056545530304DF71EED4BB7CF8A
EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 12/2012 Rev.0xF7
EMMC NAME: VTU00M , S/N: 518867895
EMMC NAME (HEX): 56545530304D00
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
H/W reset function [RST_N_FUNCTION]: 0x00
Backup saved: VTU00M_ 518867895_20160303_1528.extcsd
Done.
Processing file...D:\mobile\box's\EasyJtag\Rcp and dumps\Samsung\I9300\EMMC_ROM1_00000000_20000000.bin
Z3X EasyJtag Software ver. 2.0.7.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:855 mV
CMD Active Level:2495 mV
Input file : D:\mobile\box's\EasyJtag\Rcp and dumps\Samsung\I9300\EMMC_ROM1_00000000_20000000.bin
Writing 0020000000 bytes to 00000000 ...ROM1 (USER ROM)
Done. Write Speed: 2500 kB/s
You must select flash file first!
Checking NAND Image : D:\mobile\box's\EasyJtag\Rcp and dumps\Samsung\I9300\EMMC_ROM2_00000000_00200000.bin
File successefuly loaded!
Z3X EasyJtag Software ver. 2.0.7.3
Loading eMMC Addon Firmware... IO: 3300 mV
Box S/N: ****************, ,FW Ver.: 01.52
CMD Pullup Level:886 mV
CMD Active Level:2475 mV
HiPower™ mode is off!
eMMC Device Information
EMMC CID : 15010056545530304DF71EED4BB7CF8A
EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 12/2012 Rev.0xF7
EMMC NAME: VTU00M , S/N: 518867895
EMMC NAME (HEX): 56545530304D00
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
H/W reset function [RST_N_FUNCTION]: 0x00
Backup saved: VTU00M_ 518867895_20160303_1533.extcsd
Done.
ROM1 Are not selected , skip writing ROM1
Processing file...D:\mobile\box's\EasyJtag\Rcp and dumps\Samsung\I9300\EMMC_ROM2_00000000_00200000.bin
ROM3 Are not selected , skip writing ROM3
extCSD Are not selected , skip writing extCSD
Z3X EasyJtag Software ver. 2.0.7.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:886 mV
CMD Active Level:2475 mV
Input file : D:\mobile\box's\EasyJtag\Rcp and dumps\Samsung\I9300\EMMC_ROM2_00000000_00200000.bin
Writing 0000200000 bytes to 00000000 ...ROM2 (BOOT1 ROM)
Done. Write Speed: 838 kB/s
Box Working Mode: JTAG Pin Finder.
Starting Z3X Jtag Pin Finder...
Stage 1: Search TCK / TMS / TDI / TDO...
Get IDCODE...
JTAG Pinout Found: TCK: Pin 9 / TMS: Pin 7 / TDI: Pin 5 / TDO: Pin 13
CPU IDCODE : 0x1BA00477 Mfg.: 0x23b, Part: 0xba00, Ver.: 0x1
CPU Manufacturer: QUALCOMM , CPU Name: CORTEX A8
Stage 2: Searching TRST...
TRST Pin Found: TRST: Pin 3
Box S/N: 000000000000, ,FW Ver.: 01.55
Box Working Mode: JTAG Box.
Loading repair file: 'C:\Users\wq\Downloads\SAMSUNG_GT-P1000_boot_v2_00.rcp'
Repair File ver. : FILL ME
Repair file options. : NONE
Easy-Repair file load OK!
Using EasyRepair Mode...
Warning , you are using <a href="http://easy-jtag.com/?page_id=754">custom pinout config</a> make shure that NRST and GND on proper places!
Checking repair data...
EasyJtag Suite Classic ver.: 2.4.1.1 / wxWidgets 3.1.0-W-U started.
Operating system ver.: Windows 7 (build 7600).
For support and updates visit http://easy-jtag.com
Check security...
OK
Initialising: SAMSUNG GT-P1000 Config ver.:1.00
I/O Level set to : 2800 mV
Box S/N: 14008009DC14D073 ,FW Ver.: 01.55
Connecting to Target...
JTAG device: S5PC110
CPU IDCODE : 0x1BA00477 Mfg.: 0x23b, Part: 0xba00, Ver.: 0x1
CPU Manufacturer: QUALCOMM , CPU Name: CORTEX A8
Halting CPU...
Initialize hardware...
Starting target communication...
Detecting nand memory parameters ...
NAND flash device ID:00EC:0050 'NAND 512MB 1.8V 16-bit (Samsung)' found
NAND geometry: Blocks:00000800, Page size:1024 bytes , Block size:256 pages
NAND Writing BOOT...
NAND Write OK! Elapsed time: 2.391003s (110.414 KiB/s)
NAND Writing PIT...
NAND Write OK! Elapsed time: 0.992003s (266.128 KiB/s)
NAND Writing SBL1...
NAND Write OK! Elapsed time: 17.153027s (76.954 KiB/s)
NAND Writing SBL2...
NAND Write OK! Elapsed time: 17.045029s (77.442 KiB/s)
NAND Writing UPCH...
NAND Write OK! Elapsed time: 0.964003s (1095.432 KiB/s)
All Done.
Z3X EasyJtag Software ver. 2.4.1.1
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: ****************, ,FW Ver.: 01.55
CMD Pullup Level:2299 mV
CMD Active Level:3042 mV
Box IO Level:2800 mV
CLK Rate:14000 khz
HiPower mode is off!
---------- eMMC Device Information ----------
EMMC CID : 15010053355530304D0A53D7D4524164
EMMC CSD : D02701320F5903FFF6DBFFE18E404028
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 04/2014 Rev.0xA
EMMC NAME: S5U00M , S/N: 1406653522
EMMC NAME (HEX): 53355530304D00
EMMC ROM1 (Main User Data) Capacity: 3728 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x08] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x08.
H/W reset function [RST_N_FUNCTION]: 0x00
High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00000000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x03
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: S5U00M_1406653522_20161115_1330.extcsd
Done.
Running:SAMSUNG: MoviNAND Factory Reset...
Skip loading eMMC Addon Firmware
CMD Pullup Level:2299 mV
CMD Active Level:3042 mV
Box IO Level:2800 mV
CLK Rate:14000 khz
Sending Smart Wipe Request...
Wiping Card... Please do not touch it!
<font color="red">Please don't forget to repair extCSD from backup!</font>
Done.
Running:SAMSUNG: MoviNAND Reset + Format...
Z3X EasyJtag Software ver. 2.4.1.1
Skip loading eMMC Addon Firmware
CMD Pullup Level:2299 mV
CMD Active Level:3042 mV
Box IO Level:2800 mV
CLK Rate:14000 khz
EMMC ROM2/3 (Boot Partitions) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Sending Internal Reconfiguration Request...
Waiting configuration Apply!
Restoring configuration...
EMMC ROM2/3 (Boot Partitions) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Wiping Card... Please do not touch it!
<font color="red">Please don't forget to repair extCSD from backup!</font>
Done.
extCSD file...D:\mobile\box's\EasyJtag\Rcp and dumps\Samsung\S5282\SAMSUNG_GT-S5282_dump_rom1_rom2_extcsd\S5U00M_2946020930_20150001_1827.extcsd
Running:Repair extCSD...
Z3X EasyJtag Software ver. 2.4.1.1
Skip loading eMMC Addon Firmware
CMD Pullup Level:2299 mV
CMD Active Level:3042 mV
Box IO Level:2800 mV
CLK Rate:14000 khz
Writing...
Done.
Checking NAND Image : D:\mobile\box's\EasyJtag\Rcp and dumps\Samsung\S5282\SAMSUNG_GT-S5282_dump_rom1_rom2_extcsd\EMMC_ROM1_00000000_40000000.bin
File successefuly loaded!
Found ROM2 and automatically selected.
Found EXT CSD and automatically selected.
Processing file...D:\mobile\box's\EasyJtag\Rcp and dumps\Samsung\S5282\SAMSUNG_GT-S5282_dump_rom1_rom2_extcsd\S5U00M_2946020930_20150001_1827.extcsd
Processing file...D:\mobile\box's\EasyJtag\Rcp and dumps\Samsung\S5282\SAMSUNG_GT-S5282_dump_rom1_rom2_extcsd\EMMC_ROM1_00000000_40000000.bin
Processing file...D:\mobile\box's\EasyJtag\Rcp and dumps\Samsung\S5282\SAMSUNG_GT-S5282_dump_rom1_rom2_extcsd\EMMC_ROM2_00000000_00200000.bin
ROM3 Are not selected , skip writing ROM3
Running:Repair extCSD...
Z3X EasyJtag Software ver. 2.4.1.1
Skip loading eMMC Addon Firmware
CMD Pullup Level:2299 mV
CMD Active Level:3042 mV
Box IO Level:2800 mV
CLK Rate:14000 khz
Writing...
Done.
Z3X EasyJtag Software ver. 2.4.1.1
Skip loading eMMC Addon Firmware
CMD Pullup Level:2299 mV
CMD Active Level:3042 mV
Input file : D:\mobile\box's\EasyJtag\Rcp and dumps\Samsung\S5282\SAMSUNG_GT-S5282_dump_rom1_rom2_extcsd\EMMC_ROM1_00000000_40000000.bin
Writing 0040000000 bytes to 00000000 ...ROM1 (USER ROM)
Done. Write Speed: 1406 kB/s
Z3X EasyJtag Software ver. 2.4.1.1
Skip loading eMMC Addon Firmware
CMD Pullup Level:2299 mV
CMD Active Level:3042 mV
Input file : D:\mobile\box's\EasyJtag\Rcp and dumps\Samsung\S5282\SAMSUNG_GT-S5282_dump_rom1_rom2_extcsd\EMMC_ROM2_00000000_00200000.bin
Writing 0000200000 bytes to 00000000 ...ROM2 (BOOT1 ROM)
Done. Write Speed: 1303 kB/s