رد: طلب فلاشة gfive gpad 706 plus
هل من وجد فلاشة لهذه التابلات؟
هي من نوع MTK NAND و غير مدعومة على cm2 (على ما أظن و الله أعلم)
ما يلي log read info (جربت جميع خيارات nand init mode):
Operation : Check / Read Info [ v1.58 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 102 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : 004500DE009400930076005000080000
eMMC Flash : NOT INSTALLED
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x0053 , NAND_UNKNOWN
[NAND] : FLASH_DIE : 0045 00DE 0094 0093 0076 0050 0008
[NAND] : FLASH_LEN : 0x200000000
[NAND] : FLASH_EXT : 4000/0100/00
DEV RID : 0x9D29877D078208A715BD48970C93248A
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Info read not done
Erased/damaged phone?
You can change settings : Settings -> Other -> NAND init Mode
Done!
Elapsed: 00:00:06
Reconnect Power/Cable!
***********************************************
read firmware + nand extra log
Operation : Read Flash [ v1.58 ]
Power Off Phone , re-connect battery , Insert USB cable!
Wait for phone...
Phone found! [ 102 ]
Sync...
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 102 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : 004500DE009400930076005000080000
eMMC Flash : NOT INSTALLED
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x0053 , NAND_UNKNOWN
[NAND] : FLASH_DIE : 0045 00DE 0094 0093 0076 0050 0008
[NAND] : FLASH_LEN : 0x200000000
[NAND] : FLASH_EXT : 4000/0100/00
DEV RID : 0x9D29877D078208A715BD48970C93248A
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Reading Flash Content now ...
[Read Error] : Bad PRELOADER data
Looks like unusable file , break!
Done!
Elapsed: 00:01:03
Reconnect Power/Cable